5 Axis CAD CAM zirconia dental Milling Machine for Crown Bridge

 

This 5 Axis CAD CAM zirconia dental Milling Machine  is used for the processing of restorations such as crowns and bridges. It adopts advanced five-axis linkage technology and has a precise and efficient milling process. In terms of the body material, the equipment adopts a high-strength cast iron frame with excellent seismic resistance and stability, which can effectively reduce vibration during high-speed operation and ensure the maintenance of precision during milling. The inside and outside of the body are precision machined to ensure that the structure is strong and durable, and it is not easy to deform after long-term use. The operating system rods and worktables of the machine tool are designed with corrosion-resistant coatings, which effectively extend the service life of the equipment and maintain an excellent working environment. The bottom of the equipment adopts a solid anti-vibration pad foundation to reduce the impact of small vibrations generated during the processing on the processing accuracy. The built-in intelligent cooling system adopts efficient coolant circulation to keep the tool and workpiece at the best temperature during long-term processing, avoiding processing errors or material damage caused by excessive temperature. It can perform fine cutting at multiple angles and directions (Aaxis +-360°B axis: 25-115°), while ensuring that the processing surface is smooth and smooth with high reproducibility.

 

The size of the milling material	98mm,98.5mm and the max thickness is 80mm
The max speed of XYZ axis	Z axis 4000mm/min XY axis 6000mm/min
The max speed of the spindle	6000-60000 rotation/min
The angle of the axis	Aaxis +-360°B axis :25-115°
The type of milling burs	Auto milling burs installation
The amount of milling burs	DiameterΦ 4*56mm
Controlling instruction set	NC code
Interface	USB 2.0.100M Internet access
Voltage	220V +-10%,50/60 Hertz
Power Consumption	Noise-pollution level
Noise-Pollution level	Standby model : under 45 decibel milling model: under 70 decibel The data was tested by UT353, the level of the noise varies when different material is used.
Install conditions	Indoor installation altitude below 2000m,temperature :5-40 degree Celsius
The size of the machine	470*560*650mm
Weight	90kg

 

 

 

 

1.Intelligent tool management system

5 Axis CAD CAM dental Milling Machine for Crown Bridge uses advanced tool management technology to achieve dynamic management of tool positions through pre-programmed algorithms. The system supports flexible scheduling between 8 to 14 different tools. When the device detects that the cutting task is suspended, it will automatically close the tool compartment in a relatively closed area, using the built-in protection mechanism to block the entry of external impurities, ensuring that the machine environment is clean and the tool is in the best condition.

2.The machine tool has completed internal parameter optimization before delivery, and automatically loads the preset parameters and activates the self-check program when it starts. The embedded self-calibration algorithm ensures that each startup is in the best working condition without additional manual intervention or external correction.

3.The motion system of the device adopts multi-degree-of-freedom synchronous linkage technology to achieve 360° continuous cycle motion of the spindle, and provides a wide range of tilt angles through the auxiliary rotation mechanism to meet complex processing requirements. (Aaxis +-360°B axis: 25-115°) allows the device to enter the processing area from any angle when finely cutting crown and bridge components, improving the flexibility and accuracy of engraving.

4.Cloud-connected remote control
Operators can use dedicated software to monitor the status of the equipment in real time, adjust process parameters and remotely diagnose faults at any location.

5.It has a unique 100° blank holder. The uniquely designed clamping mechanism enables the equipment to achieve precise control of the angle and fixing force of the raw material. This patented technology uses precise calculation and force feedback systems to optimize the cutting path while maintaining the stability of the raw material, making material cutting more efficient. This fixing method can make full use of the raw material and save up to 30% of material waste compared to traditional solutions.

 

 

 

 

 

 

 

 

 

 

Hot Tags: milling machine ,cad cam machine ,dental lab machine,dental lab ,cad cam