1. Precision & Efficiency Revolution Driven by 5-Axis Technology

(1) Single Clamping - Zero Worries From Start to Finish

Eliminates repositioning errors:
Traditional 3-axis systems require 2–3 reclampings, introducing ±0.02–±0.05 mm cumulative errors.
A 5-axis system completes all procedures in one single setup, keeping total deviation within ±0.01 mm.

Reduced auxiliary time:
Clamping time decreases from 30 minutes to 5 minutes, increasing single-unit productivity by 40%+.

Handles complex morphologies with ease:
Ultra-thin veneer margins (0.3–0.5 mm) and box-shaped inlay geometries are milled without tool interference.

(2) Full Freedom of Angulation - Unlocking Unlimited Design Potential

Undercut capability:
A/C-axis rotation allows the tool to approach undercut areas perpendicularly-no special fixtures required.
Ideal for custom abutments, implant components and anatomically complex restorations.

High-definition occlusal textures:
5-axis simultaneous motion mills 0.1 mm–precision grooves, mimicking natural occlusal morphology.

Bridge connector optimization:
For 3–4 unit bridges, connector thickness is controlled at 1.5–2.0 mm, increasing structural strength 20%.

2. Advantages of Wet Milling for Glass Ceramics

(1) Material Protection - Significantly Reduced Chipping

Thermal-shock prevention:
Glass ceramics have low thermal conductivity (1.2–1.5 W/m·K).
Dry milling causes localized overheating and microcracks.
Wet milling keeps temperature under 50°C, reducing chipping by 60%.

Reduced cutting stress:
Water lubrication lowers friction and cutting force by 30%, ideal for brittle glass-ceramic materials.

Superior surface quality:
Wet-milled surfaces achieve 50% lower roughness, cutting post-polishing time in half.

(2) Efficient Debris Removal & Extended Tool Life

Real-time chip evacuation:
High-pressure water flushes out ceramic particles (<10 μm), preventing secondary scratches.

Extended tool durability:
Diamond tools last 2–3× longer due to combined cooling and lubrication-greatly reducing consumable costs.

3. Superior Adaptability for Glass-Ceramic Materials

(1) Material-Specific Milling Strategies

Layered cutting approach:
Rough (remove 70%), semi-finish (20%), finish-cut (10%)
- each layer controlled at 0.05–0.2 mm to avoid stress accumulation.

Edge enhancement strategy:
"Rounded transition + low-speed finishing" on the most fragile margins increases edge strength by 30%.

(2) Multi-material Capability

Compatible with glass ceramics, PMMA, wax, and titanium premill abutments, supporting true "all-in-one" milling.

Fully open system compatible with Exocad, 3Shape, HyperDENT, ensuring seamless digital workflow integration.

4. Clinical Value & Real-World Application

(1) Chairside Same-Day Dentistry

Complete workflow-from scanning to final placement-within 1.5–2.5 hours.

Ideal for anterior aesthetic cases such as veneers and full crowns.

Perfect for emergency situations where temporary crowns/bridges must be produced immediately.

Increases patient satisfaction by 40%+.

(2) Productivity Boost for Dental Laboratories

Daily output of 100–300 units, 2–3× higher than traditional 3-axis machines.

Supports overnight unattended milling, increasing equipment utilization by 50%.

High accuracy results in 60% fewer remakes, boosting profitability.

Overall unit cost reduced by 20%.

5. Intelligent Control & Safety System

(1) Smart Monitoring & Real-Time Alerts

Monitors spindle load, water pressure, and tool wear in real time.

Auto-stop + alarm when abnormalities are detected, preventing material waste.

Automatic calibration system compensates mechanical deviation at startup, ensuring long-term accuracy.

(2) Multi-layer Safety Protection

Fully enclosed wet-milling chamber prevents ceramic dust and splashes-protecting operator health.

Complies with ISO 13485 medical equipment safety standards.

Overload protection, leakage protection, and emergency stop button included.

Spindle thermal protection:
Automatically reduces speed when temperature exceeds 60°C, extending machine lifespan.

 

 

 

 

 

Advantages：

1.Our C5M milling machine can mill glass ceramics, Titanium premill abutment, titanium disc ,pmma.

2.We use multiple holder

3. Our strong R&D ability always can guide the trending of China milling machine market. Some others followed our steps and copied our machine.

4. We use global famous parts,Japan THK guide rail ,THK screw rod, Japan Panasonic servo motor etc.

5. Our tool magazine can be hided when not use. It will protect milling bur life longer.

5. We support OEM &ODM for dealers

6.We have CE certificate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After-sales service：

1. One year hardware warranty (Not include milling bur). If happened problem,will supply free parts to replace

2. Permanent software service.

3. Supply online free training for customer's technician

4. 24 hours can be available to contact our sales

Hot Tags: glass ceramic 5 axis dental Milling Machine, China, suppliers, manufacturers, factory, customized